礦用振動篩動不動就壞了？你有想過嗎》這可能不是它的問題，而是你的維護除了問題？礦用振動篩的維修保養至關重要,合理的維修可以延長使用壽命。那么，如何維護和保養礦用振動篩呢？

　　一、礦用振動篩日常維護

　　礦用振動篩日常維護內容包括篩子表面，礦用振動篩特別是篩面緊固情況，礦用振動篩松動時應及時緊固。礦用振動篩定期清洗篩子表面，礦用振動篩對于漆皮脫落部位應及時修理、除銹并涂漆，對于裸露的加工表面應涂以工業凡士林以防生銹。

　　二、礦用振動篩定期檢查

　　礦用振動篩定期檢查包括周檢和月檢。

　　1、礦用振動篩周檢：檢查激振器、篩面、支承裝置等各部螺栓緊固情況，礦用振動篩當有松動時應加以緊固。檢查傳動裝置的使用狀況和連接螺栓的鎖緊情況，礦用振動篩檢查三角帶張緊程度，必要時適當張緊。礦用振動篩檢查篩子時，礦用振動篩須特別注意查看在飛輪上的不平衡重塊固定得是否可靠，如固定不牢，篩子運轉時，礦用振動篩不平衡重塊就可能脫離飛輪，導致安全事故。

　　2、礦用振動篩月檢：檢查篩面磨損情況，礦用振動篩如發現明顯的局部磨損應采取必要的措施(如調換位置等)，并重新緊固篩面。礦用振動篩檢查整個篩框，礦用振動篩主要檢查主梁和全部橫梁焊縫情況，礦用振動篩并仔細檢查是否有局部裂紋。檢查篩箱側板全部螺栓情況，礦用振動篩當發現螺栓與側板有間隙或松動時，礦用振動篩應更換新的螺栓。

　　三、礦用振動篩維修時應特別注意

　　1、激振器及傳動裝置拆卸應由有經驗的技術工人進行，礦用振動篩嚴禁野蠻操作，礦用振動篩防止損壞設備。礦用振動篩裝配前應保持零件潔凈。

　　2、礦用振動篩更換后的新篩網應每隔4-8h重新張緊一次，礦用振動篩直到完全張緊為止。